Electrician Services in Northwest Pasco, Pasco, WA

Why Northwest Pasco Homeowners Call Young’s

What We Handle in Northwest Pasco

• Electrical panel and meter upgrades – Including coordination with Franklin PUD for the meter and service side.
• EV charger installation – Which here genuinely depends on which era of house you’re in.
• Circuits added for modern loads – Home offices, shops, hot tubs and kitchens.
• Breakers that keep tripping – Diagnosed properly rather than replaced and hoped for.
• Outlet, switch and circuit repairs – Including dead outlets, loose devices and aged-out GFCIs.
• Wiring and rewiring – For remodels, additions and circuits that were never adequate.
• Indoor and outdoor lighting – Including LED retrofits.
• Whole-house surge protection – Worth adding before new HVAC equipment, not after.
• Solar panel installation and energy audits – And the electrical work that goes with them.

100-Amp or 200-Amp? It Decides Everything

In a neighborhood spanning two building eras, the single most useful thing to know about your house is the size of its electrical service — because it determines what you can add and what it will cost.

The number is on the main breaker at the top of your panel. A newer Northwest Pasco home is almost certainly 200 amps, which comfortably supports modern life including an EV charger. An older one may be 100 amps, which was entirely adequate when it was installed and is increasingly tight now. A 100-amp service running a furnace, an electric water heater, a range and a dryer has meaningfully less headroom for a car charger or a hot tub than most homeowners assume.

This is not a reason to panic or to upgrade pre-emptively. Plenty of 100-amp homes run perfectly well and will continue to. But it does mean that if you are planning an EV charger, a shop or a significant remodel, the load calculation is a real gate rather than a formality — and it is worth doing early, because the answer changes the budget for everything downstream. Where capacity is genuinely short, a load-management device is often several times cheaper than a full service upgrade, and it is an option many homeowners are never offered.

What Happens When We Come Out

1. You call or book onlineTell us what you’re trying to add or what’s misbehaving.
2. Assessment on arrivalFor new circuits that means a load calculation and a look at the panel; for faults it means tracing the actual cause.
3. Upfront quote before any workAn exact price and your options in plain language, including permit and utility coordination where it applies.
4. The workDone to current code, by licensed electricians, with the inspection handled.
5. Test and verifyWe confirm everything is working and safe before we leave.

Signs Your Panel Needs Attention

What you’re seeing	What it usually means
100-amp main breaker and big plans	Load calculation first. It decides the budget for everything else.
Breakers tripping under normal load	Circuit shared too heavily for modern use, or a developing fault.
No spare spaces left in the panel	A subpanel or panel upgrade, depending on what you’re adding.
Warm panel cover, buzzing, or a burning smell	Stop and call. This is the urgent category.
A GFCI that won’t trip when tested	Failed safety device. Replace it — it is a small job.

Keeping It Running

• Find out what size your service is — the number is on the main breaker at the top of the panel. It’s worth knowing before you plan anything.
• Test GFCI outlets monthly — press test, confirm the power cuts, press reset.
• Don’t keep resetting a breaker that trips regularly. It’s reporting a real limit.
• Get an electrical inspection before a major remodel or after DIY work by a previous owner.

Frequently Asked Questions

Who is my electric utility?

Franklin PUD. That’s different from Kennewick, which is served by Benton PUD, and different again from Richland, which runs its own city-owned utility. It matters mainly for meter work, service upgrades and new connections. We coordinate with Franklin PUD regularly.

How do I find out if I have a 100-amp or 200-amp service?

Look at the main breaker at the top of your panel — the rating is printed on it. In Northwest Pasco it varies by the age of the house, and it’s the single most useful thing to know before planning an EV charger, a shop or a remodel.

Can a 100-amp home take an EV charger?

Sometimes, but it’s a genuine question rather than a formality. It depends on what else is electric in the house and how those loads coincide. Where capacity is short, a load-management device that lets the charger back off when the house is drawing hard is often several times cheaper than a service upgrade — and many homeowners are never told it exists.

Should I upgrade my service pre-emptively?

Not usually. Plenty of 100-amp homes run perfectly well. Upgrade when a specific project requires it, and get the load calculation done early enough that the cost is part of the plan rather than a surprise.

Do you pull permits?

Yes, where the work requires them, and we handle the inspection. Electrical work done without a permit can cause problems at resale and is not worth the shortcut.

A breaker keeps tripping. Can I just replace it?

Please don’t. A breaker that trips is usually doing its job — it’s reporting a problem on the circuit rather than being the problem. Replacing it with a larger one removes the protection without fixing the cause.

Do you do electrical and HVAC on the same visit?

Yes. We’re licensed for HVAC, electrical and plumbing in-house, which is the main reason customers stay with us — one contractor who already knows the house, instead of three scheduled on three different days.

Schedule an Electrician in Northwest Pasco

Find out what you’ve actually got before you plan around it. Call (509) 525-4328 or book online, and see our full electrical service page.

More Northwest Pasco Services